后挖沟深度对深海海底管道屈曲影响数值分析     

李修波  刘可安  王华昆  王鸿飞 《海洋工程》2020,38(3):152-160

鉴于海底管道的服役水深越来越深,主要采用犁式挖沟机对预铺设于海床之上的海底管道采取后挖沟的方式将海底管道埋设于海床之下,以保护其免受不必要的损伤。针对后挖沟深度H是海底挖沟机的重要设计参数,也是影响管道悬跨的重要因素的问题,对SMD(UK)犁式挖沟机展开参数优化,确保作业过程中悬跨段管道在外部静水压力作用下,海底管道不会发生屈曲破坏。采用ABAQUS软件,分别建立了作业前和作业中两种工况下的悬跨模型,分析机械手对接触部分管道的损伤,结果显示,作业中的机械手对悬跨管道的损伤更大;同时,建立了作业中不同管径下,后挖沟深度对管道损伤的安全裕量关系曲线。进一步,结合作业中不同挖沟深度下的管跨段屈曲数值模型,对处于外部静水压力作用下的悬跨管的屈曲失效展开分析,结果显示,随着后挖沟深度的加大,不同管径下的悬跨段管道局部出现塑性压溃的临界压力值不断降低;管道外径的增大,降低了同一后挖沟深度下发生屈曲失效的压力值。最后,在后挖沟深度与外部静水压力组成的区域内,建立屈曲失效临界关系曲线,并划分出工作区和压溃区,为深海管道后挖沟埋管的施工提供工程参考。  相似文献   

柔性水囊潜堤消波特性的溃坝水槽试验研究     

陈本毅  赵西增  刘竹琴  周琪坤  卞婧 《海洋工程》2020,38(5):71-79

柔性水囊潜堤由橡胶制成，内部充水，具有结构简单、造价低廉等优点，能较好满足人工岛、跨海桥梁、海洋平台等基础设施建设工程对简单便携、拆装方便的临时防波堤的需求。为了探究柔性水囊潜堤的消波特性，在溃坝水槽内开展溃坝波与半圆柱形柔性水囊潜堤相互作用的试验研究，重点探究柔性水囊潜堤与溃坝波相互作用过程中水位变化特性，并与半圆柱刚性潜堤的性能进行比较；同时分析柔性水囊潜堤内部初始水压和浸没深度等参数对其消波性能的影响。结果表明：柔性水囊潜堤能够用作临时防波堤来衰减波浪；与半圆柱刚性潜堤相比，柔性水囊潜堤在降低溃坝波无量纲最大水位、提高消波性能方面更具优势；内部初始水压是影响柔性水囊潜堤消波性能的重要因素，适当降低内部初始水压，有利于增强柔性潜堤的变形程度，进而增加波能耗散，可获得更好的消波效果；而增加浸没深度即潜深，会使得柔性水囊潜堤对溃坝波的影响程度降低，消波效果减弱。  相似文献   

北部湾地区海砂填料的动力特性分析     

王家全  陈胜前  唐毅  黄世斌  黄钦政 《海洋工程》2020,38(5):149-155

为研究北部湾地区海砂填料的动力特性，采用高级动态三轴测试系统开展循环荷载下的动三轴试验，研究不同围压及不同动应力幅值对海砂动力特性的影响规律。试验结果表明：轴向累计应变随围压增加而减小，围压150 kPa时振次10 000后应变仅为3%；随着动应力幅值的增大轴向累积应变随之增大，且达到破坏标准的时间越短。动弹性模量随着动应力幅值和围压的增加而增大，不同围压下动弹性模量随动应变的增加出现先骤减再略减后稳定的发展趋势，ε_d>0.3%后开始趋于稳定；不同动应力幅值下动弹性模量出现先增后减直至稳定的趋势，其中动应力幅值对动弹性模量有明显的影响，围压影响相对较小。孔压比随动应力幅值增加而减小，随围压增加而增加。  相似文献   

Impacts of confining pressure and safety thickness on water and mud inrush in weathered granite     

Jinquan Liu  Weizhong Chen  Zhiping Deng  Taogen Liu 《Marine Georesources & Geotechnology》2020,38(2):144-153

Abstract

Due to the strong disintegration and water erosion of completely weathered granite, water and mud inrush disasters are apt to take place in this zone during underwater tunnel construction. The pore, compactness, seepage path length, fracture geometries and their interconnections for water and mud transfer are strongly influenced by confining pressure and waterproof-resistant slab safety thickness. In order to inspect the influence, a series of experiments based on a self-designed testing system and non-Darcy testing method were performed. The results indicated that the water and mud inrush evolution increased with the increase of confining pressure and decreased with the increase of safety thickness. In particular, the confining pressure mainly influences the initial evolution stage, and a critical safety thickness to prevent water and mud inrush is obtained. Besides, the non-Darcy testing method results shows that the water and mud inrush evolution affects the influence of non-Darcy flow. For example, while the safety thickness was smaller than the critical value, the evolution was large and unstable and its behavior transferred into nonlinear. In this case, the flow changed to non-Darcy flow.  相似文献   

Effect of microstructure on stress–strain and pore-pressure response of sabarmati sand under the influence of mica     

P. Seethalakshmi 《Geomechanics and Geoengineering》2020,15(2):123-139

ABSTRACT

Micaceous soil is believed to be detrimental for civil engineering constructions due to the effect of high compressibility, low compacted density and low shear strength. Individual mica particle has numerous intact mica flakes foliated over each other making it flexible upon loading and rebound upon unloading due to its low hardness and resilient nature. Hence, micaceous soils with mica content more than 10% are considered undesirable for highway pavements, embankments and railway track constructions. When platy mica particles are sufficiently numerous to interact with spherical sand particles, bridging and ordering phenomena are augmented within the soil mass creating unique sand-mica particle orientation (MS microstructure) unlike sand-sand particle orientation (PS microstructure). The current experimental research was conducted to evaluate the variation in stress–strain, pore pressure and effective stress path response of Sabarmati sand under the influence of mica (sand with 30% mica and pure sand) with MS and PS microstructure respectively. Effect of particle crushing on stress–strain and pore pressure response was also studied on Sabarmati sand with MS and PS microstructure. Distinctive macroscopic response was observed in Sabarmati sand with MS microstructure under the influence of mica as well as mica particle crushing.  相似文献   

AN EXPERIMENTAL STUDY ON THE PROCESS OF INTERGRANULAR PRESSURE SOLUTION OF PLAGIOCLASE GOUGE UNDER HIGH TEMPERATURE AND PRESSURE: METHOD AND PRELIMINARY RESULTS          下载免费PDF全文

ZHANG Shu  HE Chang-rong 《地震地质》2019,41(4):1012-1026

To understand the mechanism of lower-crust earthquake and slow slips, it is necessary to study the frictional properties of mafic rocks and their major rock-forming minerals. Previous studies have performed a series of experimental researches on gabbro, basalt and their major constituents. According to the results of previous experiments, frictional sliding of plagioclase under hydrothermal conditions(100~600℃)shows a property of velocity weakening, and the experimental results show that both the direct rate effect parameter(a)and the healing effect parameter(b)increase with temperature, a typical feature for thermally-activated processes. Velocity weakening means property of a shear band that has a stronger friction healing effect than the direct rate effect in the rate and state friction constitutive framework, and the healing effect(b value)in constitutive relation mainly reflects the increase in contact area with time under hydrothermal conditions, with some minor effect of structural changes. Since the microphysical mechanism of feldspar minerals at the contacts is mainly brittle cataclasis for temperatures below 600℃, the significant frictional healing effect in this case can only be explained by the mechanism of pressure solution. In order to determine if the dissolution process of plagioclase actually occurs on the laboratory time scale, we conducted hydrostatic experiments on plagioclase powder samples under hydrothermal conditions whereby frequent contact switch between particles seen in frictional sliding experiments can be avoided, making the observation on the dissolution sites possible. Experimental temperatures were 400℃ and 500℃, with confining pressure of 90~150MPa, pore pressure of 30MPa, with 2mm initial thickness of fault gouge. The mechanical data show that a creep process occurred in the plagioclase fault gouge in the experimental temperature and pressure range; and the microstructures of the experiment show that precipitation of new grains is prevalent as the product of pressure solution process between plagioclase particles. At the same time, it is observed that the contact points have an appearance similar to fused, fuzzy structure as signatures of dissolution. The results of our experiments provide a definite experimental evidence for the healing mechanism in friction of plagioclase and for the theoretical relation between unstable slip and the pressure solution process. The results of the experiments are summarized as follows: (1)Drainage rate of pore water in plagioclase gouge was high in the first few hours of experiment, but gradually decreases over time for both temperature and pressure series of experiments slowing down to a steady state. This feature indicates that there is a creep process that evolves inside the plagioclase gouge. In the temperature-series experiments, the drainage rate of the pore water in the plagioclase gouge at 400℃ is relatively low than the cases for higher temperatures. Thus, the applied temperature is positively correlated with the creep of plagioclase gouge. (2)Scanning electron microscopy(SEM)observations of the experimentally deformed samples were performed on thin sections cut along the sample axis. Firstly, from the images of microstructure, it was found that the degree of particle fracture became more significant at a higher effective pressure, with smaller pore volume between particles. In the temperature-series experiments it was found that the degree of compaction of plagioclase gouge increased with increasing temperature. Precipitation of plagioclase grains in layered structures was generally observed in high-magnification images, indicating the presence of pressure solution processes. Contact points were also found to be in a state of ambiguity that seems to be a fused morphology, but the details of the structure remain to be determined by further observations. The above results indicate that the pressure solution process of plagioclase particles can occur on a typical laboratory time scale, and the results of this study provide robust experimental evidences for the theory that links between pressure solution and the mechanism of frictional healing and unstable slips for plagioclase.  相似文献   

景观建筑挡土墙优化设计后抗震性能的实验测试研究          下载免费PDF全文

牛艳玲  王洁宁 《地震工程学报》2019,41(3):596-600

目前的景观建筑设计中往往更注重建筑的景观性,而忽略了建筑的安全稳定性,导致景观建筑的整体抗震效果较差,在景观建筑设计中加入挡土墙设计可以有效提高其抗震性。为此,设计一种具有一定抗震性能的景观建筑挡土墙,利用建筑施工过程中保留的复合纤维材料、建筑垃圾以及纤维绳等作为土墙填充物,并加入具有一定抗拉能力的拉筋材料,以保持土墙内部的稳定性。考虑景观建筑通常注重外观视觉效果,使用"平改坡"设计,在墙体表面种植具有一定视觉冲击的植物,增加土墙自重,促进土墙整体结构的稳定性。分析挡土墙后面无限倾斜填土受力状态,选取菱形微小单元体作为研究对象,计算景观建筑的挡土墙土压力强度。实验证明,优化设计的景观建筑挡土墙结构可以有效增强景观建筑的整体抗震能力。  相似文献   

飑线对定点地形变观测的影响特征与机理——以陕西关中盆地为例     

杨小林  危自根  杨锦玲  王党席 《中国地震》2019,35(3):465-475

2013年7月31日～8月1日陕西关中盆地爆发了一次强飑线灾害性天气过程,为揭示此次飑线生命史期间对定点地形变观测的影响特征与机理,本文结合多普勒天气雷达和气象资料,系统分析了关中盆地内4个地形变观测数据。结果表明:(1)飑线过境时的短时气压突变是造成定点地形变的主要原因,引起最大的地倾斜和地应变分别达9.70×10~(-3″)和21.02×10~(-9);(2)气压变幅与地形变的弹性响应量具有较好的线性关系,二者持续时间较一致,为2～4h,其中,钻孔体应变的动态气压系数达4.04×10~(-9)/h Pa;(3)宝鸡、乾陵和华阴台对飑线的响应能力较好,西安台则较差;(4)除水管仪外,垂直摆、洞体应变和钻孔体应变等对飑线的响应均较为灵敏。上述结果有助于合理识别和科学推定飑线所导致定点地形变异常变化的物理本质,进而减少实际业务中的误判;同时,还能为定点地形变观测台站的科学选址、仪器的优化布设及不同空间尺度大气负荷模型的实证等提供重要的参考依据。  相似文献   

建筑在强震下横拉承压力钢筋负荷测量          下载免费PDF全文

任燕娟 《地震工程学报》2018,40(4):692-697

在强震状态下,建筑物的横拉承压受力较为复杂,另外由于建筑物形状及在地震中受力面积大小不同,在强震下造成碰撞大小影响不一导致其横拉承压力的随机复杂性十分突出。传统的建筑承压负荷检测方法中钢筋负荷受力测量能力不足,检测结果易出现误差。将建筑钢筋的机械性能设为理想弹塑性,利用建筑物横拉承压力钢筋负荷测量方法,对不同结构、不同工况的建筑钢筋载荷的变化规律进行测试分析,结合建筑局部承压特点和整体结构聚力方式,设计横拉承压力钢筋负荷检测方法,并进行仿真实验,结果表明该方法模型所得数据更加精准,有良好的适用性。  相似文献   

利用海洋重力场变化分析洋底板块运动          下载免费PDF全文

李倩倩  鲍李峰  C. K. Shum 《地球物理学报》2020,63(7):2506-2515

洋底板块运动是地球动力学和全球变化研究的重要内容.本文根据质量迁移与地球外部重力场变化的对应关系,利用不同时期测高资料推算的1995—2019全球海洋重力场变化结果,反演分析全球洋底板块运动特征.研究表明,板块汇聚边界、板块内无震海岭、海山群、断裂带等区域重力异常变化显著,而在板块离散边界无明显变化趋势;西南印度洋中脊、大西洋中脊、中印度洋中脊等地区重力异常垂直梯度变化显著,且在西太平洋俯冲带、部分海岭区域也存在明显变化,其空间分布与地形基本吻合.海洋重力场变化整体上准确反映了全球洋底板块构造运动.相较于重力异常变化反演结果,重力垂直梯度的变化能够更为准确地反映洋底板块运动特征,特别是在洋中脊区域,扩张速率越小,垂直重力梯度变化越显著.此外,详细讨论了测高海洋重力场不确定因素对洋底板块运动分析结果的影响,海面坡度改正是主要因素之一.  相似文献